HTZ™ TRUGRIP
™
Long Life Post Frame Fasteners
Applications
 | Roof and wall panel to wood structure. |
| Panel over insulation to wood structure. |
| Stitch roof and wall panel. |
Product Features
| Integral washer head design seals even when driven at an angle. |
| Zinc die-cast head most preferred fro galvalume ling life panels. |
| #10 Hi-Lo thread has 30% greater pullout than #9 in wood. |
| Climaseal long life finish resists corrosive elements in wood. |
| Type 17 point for fast cutting and easier tapping. |
Product Specifications
Diameter........#10 and #12
Thread Form.....10-16 Hi-Lo and 12-14 Double Lead
Head Style......1/4" Across Flats HWH
(Zinc die-cast)
Washer Style....7/16" O.D. Integral Head with EPDM Washer
Drill Point.....#10: Type 17
#12: Gimlet
Finish..........Climaseal® long life finish
Head Style
| 1/4" HWH zinc-aluminum alloy with integral washer design. |
Corrosion Resistance
| HTZ will never rust .... EVER!!!! |
Selector Guide
| Part# | Description | Head Style | Drill Point | Drill & Tap Capacity | Max Material Attachment | Box Qty | Common Applications |
| 1982000 | 10-16" x1 | HTZ | Type 17 | .012-.048 | 0-.250 | 2,500 | Roof and wall panel to wood structure Panel over insulation to wood structure |
| 1984000 | 10-16" x 1-1/2" | HTZ | Type 17 | .012-.048 | 0-.750 | 2,500 | |
| 1986000 | 10-16 x 2" | HTZ | Type 17 | .012-.048 | .500-1.250 | 1,000 | |
| 1988000 | 10-16 x 2-1/2" | HTZ | Type 17 | .012-.048 | 1.000-1.750 | 1,000 | |
| 1990000 | 10-16 x 3" | HTZ | Type 17 | .012-.048 | 1.000-1.750 | 1,000 | |
| 1691053 | 12-14 x 3/4" | HTZ | Gimlet | .012-.048 | - | 4,000 | Stitching of roof and wall panel |
Performance Data
| Pullout Values in Steel (average lbs. ultimate) | |||||
|
Fastener Dia. | Steel Gauge | ||||
| 26 | 24 | 22 | 20 | 18 | |
| 9 | 171 | 252 | 329 | 401 | 634 |
| 10 | 151 | 238 | 291 | 359 | 478 |
| 12 | 199 | 271 | 360 | 426 | 656 |
| Sheet Steel Gauges | |
| Gauge No. | Decimal Equivalent |
| 18 | .048" |
| 20 | .036" |
| 22 | .030" |
| 24 | .024" |
| 26 | .018" |
| 28 | .015" |
| 30 | .012" |
| Pullout Values in Wood (average lbs. ultimate) | |||||
|
Fastener Dia. | Embedment in 2" x 4" (SVP) | ||||
| 1/2" | 3/4" | 1" | 1-1/4" | 1-1/2" | |
| 9 | 198 | 328 | 571 | 728 | 872 |
| 10 | 256 | 710 | 753 | 1121 | 1358 |
| 12 | 210 | 335 | - | - | - |
| FASTENER VALUES | |||
| Fastener (dia-tpi) | Tensile (lbs. min.) | Shear (avg. lbs. ult.) | Torque (min. in. lbs.) |
| 9 | 1800 | 1200 | 50 |
| 10 | 1927 | 1200 | 71 |
| 12 | 2778 | 2000 | 92 |
| Pullover Values (average lbs. ultimate) | ||||||
| Fastener | Steel Gauge | |||||
| Dia. | 26 | 24 | 22 | 20 | 18 | |
| 9 | Washered | 515 | 674 | 875 | 1100 | 1627 |
| 10 | Washered | 548 | 932 | 1122 | 1444 | 1894 |
| 12 | Washered | 587 | 744 | 915 | 993 | - |
The values listed are ultimate averages achieved under laboratory conditions and apply to Buildex manufactured fasteners only. Appropriate safety factors should be applied to these values for design purposes.
Installation Guidelines
| A standard screwgun with a depth sensitive nosepiece should be used in install HTZ TruGrip. For optimal fastener performance, the screwgun should be a minimum of 6 amps and have a RPM range of 0-2000. |
| Adjust the screwgun nosepiece to properly seat the fastener. |
| New magnetic sockets must be correctly set before use. Remove chip build-up as needed. |
| Overdriving may result in torsional failure of the fasteners or stripout of the substrate. |
| The fastener must penetrate beyond the metal structure a minimum of 3 pitches of thread. |
| Name | |
| Title | |
| Company | |
| Address | |
| E-mail required | |
| Phone required | use xxx-xxx-xxxx format |
| FAXNumber |
Last modified: June 24, 2008
